Q2HB68MC為等角度恒力矩細分型驅動器,驅動電壓DC24-80V,適配6或8出線、電流在6A以下、外徑57-86mm的各種型號的二相混合式步進電機。q2hb68mc價格便宜,性價比高廣泛應用于雕刻機、激光打標機,激光內雕機等分辨率較高的小型數控設備上。
q2hb68mc概況:
1.DC24-80V,0.5-6A RMS(有效值)
2.細分:200-40000
3.替代型號:DQ278M,DM278M
經濟型步進電機驅動器:
Q2HB24MA,Q2HB24MB(已停產),WM234MA,WM234MB
Q2HB34MA,Q2HB34MB,Q2HB44,Q2HB44MA,Q2HB44MB,
Q2HB44MC,Q2HB44MD,Q2HB44MG,Q2HB44MH,
Q2HB68,Q2HB68MC,Q2HB68MD,
Q2HB68MG,Q2HB68MH,Q2HB88,Q2HB88M,Q2HB613,
Q2HB613M(已停產)Q2HB110(已停產),Q2HB110M,Q3HB64MA,
Q3HB64MB,Q3HB64MAB,Q3HB110M,Q3HB220M
注意
1.千萬不要將電源接反,輸入電壓不要超過DC80V。
2.輸入控制信號電平為5V,當高于5V時需要接限流電阻。
3. 此型號驅動器由于采用特殊的控制電路,故必須使用6出線或8出線電機。
4.驅動器溫度超過70度時驅動器停止工作,故障指示燈O.H亮,直到驅動器溫度降到50度,驅動器自動恢復工作。出現過熱保護請加裝散熱器。
5.過流(負載短路)故障指示燈O.H亮,請檢查電機接線及其它短路故障,排除后需要重新上電恢復。
6.欠壓(電壓小于DC24V),故障指示燈O.H亮。
細分設定表
細分?jǐn)?shù) | 1 | 2 | 4 | 5 | 8 | 10 | 20 | 25 | 40 | 50 | 100 | 200 | 200 | 200 | 200 | 200 |
D0 | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF | ON | OFF |
D1 | ON | ON | OFF | OFF | ON | ON | OFF | OFF | ON | ON | OFF | OFF | ON | ON | OFF | OFF |
D2 | ON | ON | ON | ON | OFF | OFF | OFF | OFF | ON | ON | ON | ON | OFF | OFF | OFF | OFF |
D3 | ON | ON | ON | ON | ON | ON | ON | ON | OFF | OFF | OFF | OFF | OFF | OFF | OFF | OFF |
D4 | ON,雙脈沖:PU為正向步進脈沖信號,DR為反向步進脈沖信號 | |||||||||||||||
OFF,單脈沖:PU為步進脈沖信號,DR為方向控制信號 | ||||||||||||||||
D5 | 自檢測開關(OFF時接收外部脈沖,ON時驅動器內 |