污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
北京艾諾德儀器有限公司
會員1.png)
北京艾諾德儀器有限公司
| 參 考 價 | 面議 |
產品型號GD201311030005
品 牌
廠商性質生產商
所 在 地北京市
聯系方式：李強查看聯系方式
更新時間：2022-07-12 14:52:11瀏覽次數：494次
聯系我時，請告知來自 環保在線暫無信息 |
1.輸入電壓：AC 220V
2.輸出電壓：根據所電壓擊穿試驗儀的配置
3.一次可檢測試樣100個。
4.耐壓時間在電壓擊穿試驗儀上設定。
5.獨立的保護措置：a.安全門開啟保護
汽車線束套管全自動檢測試驗臺
一、概述
本試驗臺是針對各種絕緣材料制成產品在生產線環節做在線高壓耐壓檢測使用，本試驗臺可一次檢測100個產品，通過電壓擊穿試驗儀設置好升壓速率和耐壓及裝卡好試樣后，試驗臺上下電極固定板會自動合攏，試樣夾具會自動加緊試驗，夾住試樣，并自動升壓至設置電壓，當耐壓時間到時，自動切斷試驗電壓并自動抬起到初始位置，耐壓檢測過程中，如果某一個試樣的耐壓強度不夠被擊穿時，系統會自動切斷改產品回路的電壓，并記錄耐壓時間，同時其他被測樣品耐壓檢測正常進行，被測時間到后，系統會自動提示不合格產品的標號（1-100號），當試驗完畢后方可檢出不合格產品。本試驗臺控制系統采用真彩觸摸屏顯示方式。操作軟件界面包含設置參數及試驗參數等可選項，系統運行可靠，故障率極低，可以運用在生產線上大批量檢測絕緣類產品。
二、技術指標：
1.輸入電壓：AC 220V
2.輸出電壓：根據所電壓擊穿試驗儀的配置
3.一次可檢測試樣100個。
4.耐壓時間在電壓擊穿試驗儀上設定。
5.獨立的保護措置：a.安全門開啟保護
b.獨立保護接地
c.升和下降鍵為互鎖保護
d.試驗臺上部四周有絕緣玻璃防護
6.每臺儀器配兩套負極電極。
7.做完一次實驗后，可以通過一次性把100個試樣拿出來，同時把另一個裝滿100個試樣的負極放進去，操作簡單，提高實驗效率。
8.通過氣動裝置能夠自動調節高壓的電極升降
9.通過氣動裝置控制高壓端電極，能夠自動夾緊試樣。
三、儀器各個部件名稱：
1. 電源開關，打開電源開關整機處于帶電狀態
2. 上升：按下上升按鈕，正極緩慢上升，此時上升指示燈亮
3. 下降：按下下降按鈕，正極緩慢下降，到達預定位置自動停止，此時下降指示燈亮
4. zui右側為觸摸屏顯示器：
5. 負極
6. 負極裝好試樣后可直接通過滑道推進測試空間內，
自動判停裝置
7.測試試驗時，當某個產品不合格被擊穿時，自動判停裝置會自動斷開此產品的電壓且不會影響其他產品繼續測試。
8.負極的每個電極均由銅板相連zui后連接到接地裝置上，保證了操作者的安全。
9.正極內部由銅芯制成且能自動加緊試樣。
關于更多 汽車線束套管全自動檢測試驗臺 詳細資料請您
Automotive wiring harness casing automatic testing platform
One, overview
This tester is according to various insulating materials products link in the production line use online high voltage withstand test, this test bed can be a test of 100 products, through the voltage breakdown testing instrument set pressurization rate and pressure and clamping good sample, test bench under electrode plate automatically closed, specimen fixture automatic clamp to test, sample, and automatically boost to a set voltage, when the voltage time, automatic cutting off and automatic test voltage up to the initial position, the pressure test process, if the compressive strength of a specimen was not the breakdown occurs, the system will automatically cut off the voltage change product loop, and record the pressure time, at the same time other tested samples of normal pressure testing, test time, the system will automatically prompt label unqualified products (1-100), when the detection of substandard products after the test. The test bench control system using true color touch screen display mode. Software interface includes setting parameters and test parameters such as options, reliable operation, low failure rate, can be used in the detection of insulation products production line.
Two, technical indicators:
The 1 input voltage: AC 220V
2: the output voltage according to the voltage breakdown testing instrument configuration
Can detect the sample 100 3 a.
4 pressure time set in the voltage breakdown tester.
Protection processing 5 independent: A. security door opening protection
B. independent protective earthing
C. increase and decrease key interlock protection
The upper part of D. test platform surrounded by insulating glass door
6 each instrument with two sets of negative electrode.
7 after the experiment, can one-time take out 100 samples, while the other one with negative 100 sample inside, simple operation, improve the efficiency of the experiment.
8 through the pneumatic device can automatically regulate the electrode voltage
9 through the pneumatic device to control the high voltage electrode, can automatically clamp specimen.
Three, instrument parts name:
1 power switch, open the switch machine in a charged state
2: to press the up button, positive slow rise, this rise indicator light
3 down: press the down button, positive slow decline, to automatically stop the predetermined position, the down indicator light
4 the right to touch screen display:
The 5 negative
The 6 negative samples can be directly installed by slide propulsion test space,
Automatically to stop device
The 7 test, when a product is not eligible to be breakdown, automatically to stop device voltage and will not affect the automatically disconnect the products of other products continue to test.
Each of the electrodes are connected by 8 cathode copper end connected to the earthing device, ensure the safety of the operator.
9 positive by copper core made and can automatically to sample.
For more on automotive wiring harness casing automatic testing platform details please contact us
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
環保在線 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
