閥門詢價：/
：wangbo@spiraxsarcocn.com
英國斯派莎克PF61G角座閥、斯派莎克角座閥價格
斯派莎克開/關式氣動活塞角座閥PF61G/PF51G系列，結實耐用，設計緊湊，本體為316L不銹鋼/銅。使用PTFE閥頭密封確保緊密關閉。自校正的PTFT'V'型閥桿密封提供了的密封效果:
不銹鋼閥體的氣動活塞角閥還可提供對焊、法蘭和衛生卡箍等連接方式。其中PF62G對焊連接，PF63G法蘭連接，(EN1092 PIN或ANSI 150法蘭)，PF64G承接焊連接，F(xiàn)F65G, ISO2852衛生卡箍連接。
提供常開和常閉以及用于雙向流動防水錘的特殊型號。有三種不同尺寸的執行器用丁不同的應用。其他可供選擇包括:流量調節器，電感行程開關，直接安裝的電磁導閥。
本系列角閥具有廣泛的適用性，使用介質包括蒸汽，空氣中性氣體。zui高使用范圍可達20brad，180℃。.為設備制造商(OEM)和直接用戶提供了理想的開關控制方法。
英國斯派莎克氣動角座閥PM6，是設計用于蒸汽、空氣、油、氣體和真空應用的兩通不銹鋼氣動調節角閥。標準配置能用丁zui高180℃的PEEK的閥芯密封。閥體和閥芯都經過了硬化處理。
Spirax Sarco angle seat valve Introduction in English
Spirax Sarco ON / OFF pneumatic piston angle boudoir PF61G/PF51G series , durable, compact design , the body is 316L stainless steel / copper. Use PTFE seal to ensure tight shutoff valve head . Self- correction PTFT'V ' type stem seal provides the best sealing effect :
Stainless steel pneumatic piston valve angle valve also provides welding, such as flanges and sanitary clamp connections . Which PF62G welded connection , PF63G flange connection , (EN1092 PIN or ANSI 150 flanges ), PF64G undertake solder connection , FF65G, ISO2852 sanitary clamp connection .
Normally open and normally closed for two-way flow of water hammer and special models. There are three different sizes for different applications to perform Used Ding . Other available options include : flow regulator , inductors limit switch , solenoid pilot valve installed directly .
This series Angle has broad applicability , the use of media , including steam, air neutral gas . Maximum range up 20brad, 180 ℃. Providing an ideal method to switch control equipment manufacturer (OEM) and direct users.
Spirax Sarco adjusting pneumatic Angle PM6, is designed for steam, air , oil, gas and vacuum applied through two stainless steel pneumatic control angle valve . Ding highest standard configuration can spool 180 ℃ of PEEK seal . Body and spool have been hardened .
會員1.png)
