污水處理設備 污泥處理設備 水處理過濾器 軟化水設備/除鹽設備 純凈水設備 消毒設備|加藥設備 供水/儲水/集水/排水/輔助 水處理膜 過濾器濾芯 水處理濾料 水處理劑 水處理填料 其它水處理設備
永嘉天賦閥門有限公司
永嘉天賦閥門有限公司
| 參 考 價 | 面議 |
產品型號DN65
品 牌
廠商性質生產商
所 在 地溫州市
聯系方式：肖梅霞查看聯系方式
更新時間：2018-05-14 09:00:00瀏覽次數：869次
聯系我時，請告知來自 環保在線Z40W不銹鋼美標閘閥適用于石油、化工、水力、火力電站各種系統的管路上，切斷或接通
管路介質。適用介質為：水、油品、蒸汽、醋酸及弱腐蝕性、腐蝕性等介質。
不銹鋼閘閥尺寸表
型號 | 公稱通徑 | 尺寸(mm) | |||||||
L | D | D1 | D2 | b-f | z-Φd | H | D0 | ||
Z41W. | 15 | 130 | 95 | 65 | 45 | 14-2 | 44 | 170 | 120 |
20 | 150 | 105 | 75 | 55 | 14-2 | 44 | 200 | 120 | |
25 | 160 | 115 | 85 | 65 | 14-2 | 44 | 215 | 140 | |
32 | 180 | 135 | 100 | 78 | 16-2 | 48 | 260 | 160 | |
40 | 200 | 145 | 110 | 85 | 16-3 | 48 | 290 | 200 | |
50 | 250 | 160 | 125 | 100 | 16-3 | 48 | 345 | 220 | |
65 | 265 | 180 | 145 | 120 | 18-3 | 48 | 360 | 240 | |
80 | 280 | 195 | 160 | 135 | 20-3 | 88 | 385 | 280 | |
100 | 300 | 215 | 180 | 155 | 20-3 | 88 | 430 | 300 | |
125 | 325 | 245 | 210 | 185 | 22-3 | 88 | 520 | 320 | |
150 | 350 | 280 | 240 | 210 | 24-3 | 8-23 | 610 | 350 | |
200 | 400 | 335 | 295 | 265 | 26-3 | 12-23 | 765 | 400 | |
250 | 450 | 405 | 355 | 320 | 30-3 | 12-25 | 895 | 450 | |
300 | 500 | 460 | 410 | 375 | 30-4 | 12-25 | 1145 | 500 | |
350 | 550 | 520 | 470 | 435 | 34-4 | 16-25 | 1200 | 550 | |
400 | 600 | 580 | 525 | 485 | 36-4 | 16-30 | 1400 | 600 | |
450 | 650 | 640 | 585 | 545 | 40-4 | 20-30 | 1500 | 650 | |
500 | 700 | 705 | 650 | 608 | 44-4 | 20-34 | 1630 | 700 | |
600 | 800 | 840 | 770 | 718 | 48-5 | 20-41 | 1830 | 700 | |
ASTM A 312/A 312M - 95a
Seamless and Welded Austenitic Stainless Steel Pipes
This specification covers austenitic steel pipe intended for high temperature and general corrosive service. H grades in the chemical
composition table are specifically for high temperature service. Dimensions and Tolerances
Dimensions
. All standard pipe sizes and wall thicknesses may be specified, subject to manufacturing limitations. Minimum wall
thickness pipe is also covered as a supplementary requirement.
Tolerances.
ASTM pipe
Manufacture Materials
. Refer to chemical composition table.
Manufacture
. In order to comply with this specification the pipe must be manufactured by an automatic welding process using no
filler metal, or it must be a seamless pipe. If a welded pipe has a nominal pipe size greater than 14 then it may be constructed from
two longitudinal sections, and hence have two longitudinal welds. The pipe may be either hot finished or cold finished.
Heat treatment
. Refer to heat treatment table and supplementary requirement S6.
Marking on each length of pipe
: Manufacturer’s make or brand, specification number, ‘WR’ if weld repaired, ‘NPS’ and schedule,
‘NH’ if no hydrotesting performed, ‘ET’ if eddy-current tested, ‘UT’ if ultrasonic tested. (NPS = Nominal Pipe Size.)
Finish and Repair
Finish
. The surface of the pipe must be clean and free of scale and contaminating iron particles. It can be bright annealed but may
be pickled, blasted or can be passivated.
Repair by welding
. Permitted on <20% of the weld seam length of welded pipe if >NPS 6 and having a wall thickness >0.200 in
(mm). Tungsten-arc welding process is used for repairs, with filler metal to a grade as specified in A 312 (not repeated here). Weld
repairs must be identified on the pipe and in test certificate.
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
環保在線 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
